rebuildhydrauliccylinder.comPublished by Winding AI, Inc., the company that makes Mechy See the steps
Updated November 16, 2026 · prices read Nov 16

Rebuild a hydraulic cylinder: the steps, the seal kit and what it costs

To rebuild (repack) a hydraulic cylinder, take it off the machine with the load down and the pressure relieved, open the gland, replace every seal in the kit for that cylinder, check the rod and barrel, then reassemble, torque and test it. Seal kits we read cost $14.25 to $99.59; a Cat dealer’s flat-rate reseal starts at $985.

In one line: rebuild it yourself when the rod and barrel are smooth and straight; pay a shop when they aren’t; buy new when a common-size cylinder costs less than the job.

Safety first: never open a cylinder on the machine or under a raised load. Farm hydraulics run at 2,000 to 3,000 psi (NDSU). The four checks.

  • Prices read Nov 16, 2026
  • 8 ways to get it done, compared
  • Published by Winding AI, Inc., maker of Mechy

Links to Mechy carry a tracking tag; nobody paid to be listed. Who publishes this.

At a glance

What are the ways to get a cylinder working again?

The ways to get a hydraulic cylinder working again are instructions, a seal kit, a shop reseal or a new cylinder, in the order of the cards below. Prices from each seller’s own page, read November 16, 2026, in US dollars before shipping and tax.

OptionWhat you getPriceWho does the work
Maker’s repair guideSteps and torque values for one maker’s cylindersFreeYou
YouTube videosSomeone else’s cylinder, filmedFreeYou
MechySteps built from your photos and wordsFirst 3 guides free; Pro $79/yrYou
Cylinder maker’s seal kitThe seals for one cylinder series$14.25–$82.65You
Aftermarket kit by modelSeals listed by machine and cylinder number$36.74–$99.59You
Dealer’s genuine kitThe OEM seals, by serial numberDealer quoteYou
Shop or dealer resealTeardown, seals, test$985–$1,499 (Cat, flat)The shop; you remove it
New cylinderA whole new cylinder$130.70–$975You swap it
Price ranges are the lowest and highest we read; every price, link and date is on the data page.
Before you touch a wrench

Is it safe to rebuild a hydraulic cylinder yourself?

Rebuilding a hydraulic cylinder is safe to do yourself only with the cylinder off the machine, the load on the ground or blocked, and the pressure relieved, because tractor and loader systems run at 2,000 to 3,000 psi (NDSU Extension, January 2023).

1. Load down or blocked

Never work under anything a cylinder holds up without its lock or a stand (NDSU). Remove cylinders only with the unit on the ground, safety stands or blocks and the engine off (Penn State).

2. Pressure relieved

Lower the work unit and move the control valve back and forth several times (Penn State). At work, OSHA’s rule 1910.147(d)(5)(i) requires stored energy to be relieved and made safe.

3. Off the machine

JLG’s service manual: do not service a hydraulic cylinder while it is installed; remove it and relieve all pressure, and wear safety glasses (JLG T350, section 5.2).

4. Never feel for a leak

A pinhole leak can inject oil through skin with only a slight sting, and untreated it can cost a finger or hand (NDSU). Use cardboard, and see a doctor at once if it happens.

Even with nothing attached, a hydraulic system may still be pressurized (NDSU). If a cylinder holds a load you can’t lower or block, or the machine has an accumulator, stop and call the dealer.

The job

How do you rebuild a hydraulic cylinder, step by step?

Rebuilding a hydraulic cylinder means removing it with no pressure in it, opening the gland, replacing every seal in the kit, checking the rod and barrel, and putting it back in order. These steps follow Degelman’s repair guide, Surplus Center’s seal sheet and JLG’s manual; your cylinder maker’s steps win where they differ.

  1. Make it safe, then remove it

    Lower or block the load, shut the engine off and relieve the pressure (the four checks). Clean the outside, disconnect the hoses and plug the ports, then take the cylinder off.

    Sources: Degelman, preparation; JLG T350, 5.2.

  2. Drain it and clamp it gently

    Open the ports and drain the oil. Hold the cylinder in a vise without deforming the barrel; one piece of grit can damage a cylinder.

    Sources: Degelman; Surplus Center sheet I9-6887.

  3. Open the gland

    A threaded head turns off once its set screw or locking ring is loose, often with a spanner wrench in the holes in its face. A wire-ring cylinder needs the outer ring off, the head tapped in and the kit’s plastic removal ring in the groove; Degelman warns that force won’t beat a jammed ring.

    Sources: Degelman, wire ring steps 1–7; Surplus Center, step 4.

  4. Pull the rod straight out

    Draw the rod, gland and piston out in a straight line so nothing scars the bore.

    Source: Surplus Center, step 6.

  5. Take the piston off without marking the rod

    Remove the locknut, piston and gland. Never clamp the rod on its chrome.

    Source: Degelman, threaded head step 3.

  6. Strip, clean and inspect

    Lift every old seal out with a non-sharp tool (a plastic seal pick is $1.95 at Surplus Center). Clean the parts and check the bore, piston and rod for burrs and scratches; smooth light marks with emery cloth, replace anything damaged.

    Sources: Surplus Center, steps 9–11; Degelman, step 9.

  7. Fit every new seal

    Install all the seals from the kit, oil the inner seals and grease the outer ones, and slide the gland and piston on without dragging the seals over threads.

    Sources: Degelman; Surplus Center, steps 12–14.

  8. Torque the piston locknut

    Tighten the locknut to the maker’s value. Degelman’s table runs from 25–30 lb-ft for a 3/8-24 nut to 800–900 lb-ft for a 1 3/4-12 nut.

    Source: Degelman, step 10 table.

  9. Close it up

    Slide the assembly back in. On a wire-ring cylinder the head must sit flush with the tube so the inner ring snaps into its groove; Degelman says a head left proud can push out under pressure.

    Source: Degelman, steps 11–17.

  10. Test it before trusting it

    Makers disagree on how: Surplus Center cycles its small steering cylinder with compressed air; JLG says never use air to extend or retract one. On the machine, cycle it slowly with no load and nobody near. JLG’s check calls for repair at 6 to 8 drops a minute or more from a port.

    Sources: Surplus Center, step 17; JLG T350; JLG 1930ES, 4.3.

The options

Which option fits your cylinder?

Eight ways to get a hydraulic cylinder rebuilt or replaced, in the order you meet them on the job: instructions, then parts, then paying someone, then buying new; within each, cheapest first. Each card says where it falls short.

1

The cylinder maker’s repair guide

Free instructions

Cylinder makers publish their own rebuild steps. Degelman’s repair guide covers wire-ring and threaded-head cylinders with a locknut torque table; Surplus Center’s sheet lists the tools and 17 steps for its steering cylinders.

Price: free PDFs (read November 16, 2026).

Good

  • Written for that maker’s design, with its torque values
  • Free, and the kit’s maker often publishes one

Watch out

  • Only fits cylinders built like the one drawn
  • No help when what you see differs from the drawing
Read Degelman’s guide
2

Rebuild videos on YouTube

See it done first

Videos show a gland, a wire ring and a stuck piston before you meet them. On November 16, 2026, Google’s AI Overview for “rebuild hydraulic cylinder” cited nine YouTube videos among its 13 sources.

Price: free.

Good

  • You see each step before you try it
  • Many machines and cylinder types covered

Watch out

  • The cylinder in the video may not be built like yours
  • Nobody checks the steps, specs or safety
Search the videos
3

Mechy

Steps from your photos

Mechy is a repair app: you photograph the machine or part and say what’s wrong, and it builds numbered steps with a moving 3D drawing for each, safety checks first. It flags torque and pressure figures “check your manual”. It doesn’t connect to a machine or test a cylinder, so it can’t tell you why one leaks.

Price: the first 3 guides free; Pro $79 a year (mechy.si/pricing, read November 16, 2026).

Good

  • Steps for the cylinder in front of you, from your photos
  • Safety checks come before step 1

Watch out

  • Guides are written by AI and can be wrong; its sample rebuild guide awaits a mechanic’s review
  • Sends accumulator work to a pro; needs a signal; English only
See Mechy’s sample rebuild guide
4

Seal kit from the cylinder’s maker

Parts by bore and rod

Cylinder makers sell a kit for each series, by bore and rod. Surplus Center lists a Maxim kit for a 2.5 in. bore tie-rod cylinder at $14.25; Bailey Hydraulics sells Prince’s 3 in. tie-rod kit at $31.47.

Price: $14.25 to $82.65 for the six kits we read on November 16, 2026.

Good

  • The maker’s own part, matched by its part number
  • Some come with an installation sheet

Watch out

  • Same size is not same kit: a 3 x 24 in. cylinder takes a Lion, Prince or Cross kit by its marking (Oxbo)
  • No tools in the box
See Surplus Center’s kits
5

Aftermarket kit by machine model

Parts for loaders and skid steers

Parts stores sell kits matched to a machine model and its cylinder number. HW Part Store’s kit for a John Deere 300E loader lift cylinder is $52.24; a kit listing Kubota part 7J273-63400 costs $36.74 at FridayParts and $99.59 at OMB Warehouse.

Price: $36.74 to $99.59 for the five kits we read on November 16, 2026.

Good

  • Ordered by machine model, with the OEM cylinder number
  • Some include the gland removal ring

Watch out

  • Order by the loader’s model, not the tractor’s (HW Part Store)
  • Not the machine maker’s part
See HW Part Store’s kit
6

Genuine kit from the machine’s dealer

When fit is in doubt

The machine maker’s dealer sells the genuine kit by part and serial number. John Deere lists kits online, such as AH176345, listed for models 410, 419, 420, 430 and 460, but shows a price only after you pick a dealer.

Price: a dealer quote; Deere’s store and Bobcat’s store showed no price to our reader on November 16, 2026.

Good

  • Genuine part, matched to the serial number
  • The dealer can check fit before you open it

Watch out

  • No public price we could read
  • You wait on the dealer’s stock
See Deere’s kit page
7

A hydraulic shop or dealer reseal

When the rod or barrel is doubtful

A shop tears down the cylinder you bring in, reseals it and tests it. Fabick Cat’s flat rates for Cat cylinders are $985 up to a 3.5 in. bore, $1,225 to 6 in. and $1,499 over, until December 31, 2026. Independent shops quote by the hour: bids on Tarrant County, Texas’s 2022 contract ran $70 to $90.

Price: $985 to $1,499 flat for Cat cylinders at Fabick Cat; a quote elsewhere.

Good

  • Teardown, inspection and resealing in one job
  • A shop spots rod and barrel damage you might miss

Watch out

  • You still remove the cylinder (Fabick’s rate requires it)
  • Rod, piston or barrel damage costs extra
See Fabick Cat’s rates
8

A new replacement cylinder

For common tie-rod sizes

A new cylinder with the same bore, stroke, rod, mounts and ports replaces the old one. A 3 x 8 in. Maxim tie-rod cylinder is $130.70 at Surplus Center; Hydraulic Cylinders, Inc. sells a replacement for John Deere’s AW28949 loader cylinder at $975.

Price: $130.70 to $975 for the seven cylinders we read on November 16, 2026.

Good

  • New rod, barrel and seals; no special tools
  • Often cheaper than a shop for a common size

Watch out

  • Bore, stroke, rod, pins and ports must all match
  • Machine-specific cylinders cost far more
See the 3 x 8 cylinder
Rebuild, send out or replace

How do you choose between a rebuild, a shop and a replacement cylinder?

The choice between rebuilding a hydraulic cylinder, paying a shop and buying new comes down to the rod and barrel, the cylinder’s size, and what a new one costs, on prices read November 16, 2026.

Rebuild it yourself

When the rod and bore are smooth and straight and a kit exists. A Prince 3 in. tie-rod kit ($31.47), a seal pick ($1.95) and a pin spanner ($50.62) come to $84.04.

Send it to a shop

When the rod is scored or bent, the bore is marked, or the cylinder is big. Fabick Cat’s flat rate for a Cat cylinder up to 3.5 in. bore is $985, with damage extra.

Buy a new one

When it’s a common tie-rod size: a new 3 x 8 in. Maxim cylinder is $130.70, less than most shop work. A machine-specific loader cylinder is $975 new, so a $52.24 kit wins there.

More sums, and every price with its link, on hydraulic cylinder repair cost 2026.

FAQ

What do people ask about rebuilding hydraulic cylinders?

The questions below come from Google’s People Also Ask for “rebuild hydraulic cylinder”, read November 16, 2026.

Can hydraulic cylinders be rebuilt?

Yes. Most welded and tie-rod hydraulic cylinders have a removable gland and a seal kit made for them, from $14.25 for a small tie-rod kit at Surplus Center (read November 16, 2026). A bent rod or scored barrel needs new parts too, which is why Fabick Cat charges extra for rod, piston or barrel damage.

How much does it cost to get a hydraulic cylinder repacked?

A hydraulic cylinder repack costs $14.25 to $99.59 in seal kits if you do it yourself, or $985 to $1,499 at Fabick Cat’s flat rates for Cat cylinders, by bore, on prices read November 16, 2026. Independent shops quote by the hour; Tarrant County’s 2022 bids ran $70 to $90 an hour. All 28 prices.

What are the signs that a hydraulic cylinder is failing?

A failing hydraulic cylinder leaks oil at the gland, lets a raised load drift down, or moves slowly and weakly. JLG’s 1930ES service manual gives a test: with the cylinder fully extended and a port opened, 6 to 8 drops a minute or more means the cylinder must be repaired.

Do you have to take the cylinder off the machine?

Yes. JLG’s T350 service manual says not to service a hydraulic cylinder while it is installed: remove it and relieve all pressure first. Fabick Cat’s flat-rate reseal also requires the cylinder off the machine.

What tools do you need to rebuild a hydraulic cylinder?

Degelman lists the seal kit, a rubber mallet, a screwdriver, a punch, pliers, emery cloth and a torque wrench; threaded glands also need a spanner wrench. A plastic seal pick costs $1.95 at Surplus Center, and gland nut wrenches cost $50.62 to $266.62 (read November 16, 2026).

Can you reuse the old seals?

No. Degelman’s repair guide says to replace all of the seals with new ones, and a kit is cheap next to taking the cylinder apart twice: the kits we read start at $14.25.

How do I know which seal kit I need?

Find the cylinder maker’s marking or part number first, because cylinders of the same size can need different kits: Oxbo’s sheet lists Lion, Prince and Cross kits for one 3 x 24 in. cylinder. How to find the right seal kit.

How this page was checked

We read every price on the seller’s own page on November 16, 2026, in US dollars before shipping and tax, and took the steps and safety rules from the makers’ and agencies’ documents linked in each step. The full list, a CSV and each source’s date are on the data page.

Published by Winding AI, Inc., the company that makes Mechy, one of the eight options above. Published November 16, 2026 · Updated November 16, 2026.